Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Why Houston Homeowners Choose ES Windows Construction
Bradford Remodeling Co Houston provides Es Windows repair in Houston, along with construction and replacement service across the area, with crews who understand these thermally broken aluminum frames inside and out. We are not an authorized ES Windows dealer or factory service center, and we say that plainly. What we are is a disciplined general contractor that has handled ES Windows E-Series units in gut-rehab kitchens in Montrose, water-damaged second stories in Meyerland, and full hurricane-rated retrofits in Clear Lake. For a written price on ES Windows work, call (940) 289-7658. Curtis Lane runs the Houston operation, and the scope of work goes in writing before a single tool comes out.
Why Trust Bradford Remodeling Co Houston for Your ES Windows Construction?
Houston humidity does things to aluminum windows that drier cities never see. A thermally broken ES Windows frame is built to resist heat transfer, but the gaskets, rollers, and edge seals take a beating from moisture cycling. Our crews know exactly where ES Windows E-500 and E-700 units fail after ten or fifteen years in this climate, and we repair them without selling you a full replacement you do not need.
Curtis Lane grew up in Los Angeles and picked up a framing hammer before he could legally drive, then earned carpentry and construction management credentials through Los Angeles Trade-Technical College. He has run crews in the Houston market for over a decade, from full structural repairs after storm season to high-end remodels inside the Loop. He reads a scope of work the way other guys read a box score. Straight scope, straight number – that is the whole conversation.
Every Bradford technician arrives background-checked and uniformed. Every job carries a written price before work begins, and every completed project is covered by the 365-Day Done Right Promise. If the work does not hold inside that year, we come back and correct it at no charge. That is the Garrison Standard, and it applies to ES Windows work exactly the same as a full kitchen remodel.
Styles & brands we work with
Common ES Windows Construction Problems We Fix in Houston
- Fogging between panes in older E-500 insulating glass units. This is the most common call we get on ES Windows in Houston. The edge seal on an IG unit fails after years of heat and humidity cycling, and moisture gets trapped between the glass. The frame is almost always fine. We replace the IG unit, not the whole window.
- Condensation and corrosion at aluminum frame miters. When the thermal break degrades or the gaskets harden, you get cold spots at the corners. Moisture collects, then corrosion starts. In Houston’s subtropical air, this accelerates. We clean the miter, replace the gasket, and re-seal the joint before it spreads.
- Stiff or binding casement and sliding sashes. Aluminum expands in Houston heat. Worn roller assemblies and debris in the track make the problem worse. We replace rollers and hardware, clean the track, and adjust the sash so it travels square again. Often this is a two-hour fix, not a window replacement.
- Leaking frame-to-rough-opening joints. Original sealant fails after years of thermal stress and construction movement. Water finds its way behind the flange and into the rough opening. We remove the old sealant, inspect the flashing, and re-seal the joint properly. If the framing behind it is rotted, that becomes part of the scope, in writing, before we proceed.
- Failed or missing weep baffles on E-300 sliding units. Houston gets real rain. If the weep system is clogged or missing, water sits in the track and eventually finds its way inside. We clear or replace the weep baffles and verify drainage before we call a window done.
ES Windows Parts & Our Repair-vs-Replace Approach
We use ES Windows-specified replacement parts like rollers, gaskets, and hardware where fit and function depend on them. We do not claim factory authorization, and we will not mislead you into thinking otherwise. When an original ES Windows part is obsolete or the frame is structurally compromised, we say so.
The repair-versus-replace decision comes down to one check: is the sash and frame still square? If it is, we repair. A fogged E-500 IG unit with a solid frame gets a new IG unit and EPDM gaskets. A corroded miter on an otherwise sound E-300 frame gets cleaned, gasketed, and re-sealed. If the frame is racked, the thermal break is failed, or the aluminum is corroded through, replacement is the honest call, and we recommend either a current ES Windows unit or a compatible thermally broken alternative. Call (940) 289-7658 for a straight answer on your specific windows.
Our ES Windows Service Process – Step by Step
- 1
Diagnosis. We identify the specific ES Windows series on your openings, check sash square, inspect gaskets and rollers, and document what failed and why. This is a written diagnosis, not a verbal guess.
- 2
Scope and price in writing. Before any work starts, you get a line-item scope of work and a fixed price. No numbers move at the door. The Garrison Standard applies to every ES Windows job.
- 3
Repair or replacement. We install ES Windows-specified parts or new units, reset sashes, re-seal frame-to-rough-opening joints, and replace weep systems. Flashings get checked before trim goes back on.
- 4
Test and verify. We operate every sash through its full travel, check drainage, and confirm that the thermal break is doing its job. If a window does not operate smoothly, we do not call it done.
- 5
365-Day Done Right Promise. Your written guarantee is in your hand at close. Site is swept, scope is documented, and if anything fails inside the year, we return at no charge.
See the difference
Before
After
Before
After
Before
AfterES Windows Products We Service & Install in Houston
We service and install the ES Windows E-500 Series thermally broken aluminum casement and picture windows, the E-700 Impact Series for hurricane-rated openings, the E-300 sliding and single-hung residential line, and ES Windows architectural multi-panel and pocketing wall systems. For repairs, we stock common rollers, gaskets, EPDM seals, and weep baffles locally so turnaround is measured in days, not weeks. Larger architectural systems are quoted per opening with a written scope.
We Also Service These Brands
ES Windows is a meaningful part of our Houston work, but we are not a single-brand shop, and we also offer Es Windows service in Sugar Land. We also install and service KraftMaid and Wellborn cabinetry, Cambria and Silestone countertops, and Kohler fixtures. If your project touches windows plus millwork, surfaces, or plumbing fixtures, one crew handles the whole scope, and one written price covers it.
FAQs – ES Windows Construction Service in Houston
Yes, in almost every case. Fogging in an E-500 is a failed edge seal on the insulating glass unit, not a failed frame. We remove the sash, confirm the frame is still square, and reset a new IG unit with fresh EPDM gaskets and weep baffles. The frame stays in place. Full replacement is only needed when the frame itself is corroded or racked. Call (940) 289-7658 for a written diagnosis on your specific openings.
Usually the crank and hardware only. A stiff, noisy casement crank on an ES Windows unit typically comes from a worn operator, a binding hinge, or debris in the track. We replace the worn operator and rollers, clean the track, and adjust the sash. If the sash is square and the glass is clear, there is no reason to replace it. We write that finding down and stick to it.
In many cases, yes. The E-700 Impact Series can often be retrofitted into an existing opening when the rough opening is in good condition and the surrounding framing meets current wind-load requirements for the Houston area. Every retrofit requires an inspection of the rough opening, flashing, and attachment points before we commit to a scope. Call (940) 289-7658 to schedule an assessment.
That is almost always a failed thermal break or hardened gasket at the frame’s inside edge. In Houston, the humidity finds any gap where warm, moist indoor air meets the cooler aluminum frame. The moisture condenses at the sill. We replace the gasket, restore the thermal break where possible, and verify drainage. If the thermal break is fully gone, replacement is the honest recommendation.
Both. We can match your existing ES Windows series exactly, or we can upgrade you to a current E-500, E-700 Impact Series, or architectural system, depending on the opening and your goals. Since we are independent, we are not bound to a single product lineup. We give you the straight price for each option in writing and let you decide.
Here is what we charge in the Houston market for common ES Windows scopes:
| Service | Price Range |
|---|---|
| ES Windows E-500 casement sash rebuild per window | $800 – $1800 |
| ES Windows full window replacement per opening, installed | $1500 – $3500 |
| ES Windows Impact Series installation per opening, existing opening retrofit | $3200 – $7000 |
These are line-item ranges based on what we have seen across Houston properties in recent years. Your exact number depends on the series, the condition of the rough opening, and access. The price you get in writing is the price you pay. Call (940) 289-7658 for a free estimate.
Book Your ES Windows Service in Houston, TX
If you have ES Windows units that need attention, call (940) 289-7658. We will diagnose the problem, put the scope and price in writing, and stand behind the work with the 365-Day Done Right Promise. No re-pricing at the door, no unfinished work, no mess left behind. That is how we run every job in Houston.
Written by Curtis Lane, Owner at Bradford Remodeling Co Houston, serving Houston and surrounding areas.
