Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Tamko Fence Installation: The Houston Owner’s Guide
Tamko fence installation in Houston typically runs $3,500 to $9,000 for a full perimeter job, depending on linear footage, gate count, and whether we’re pulling old posts or setting new ones. If you’re holding a Tamko product spec sheet or have a section of failed fence that matches what the builder installed, we can match the profile and color line and get it quoted the same week. Most Houston homeowners discover the problem after a storm snaps a post at the base, or when the bottom rail starts pulling free from years of ground-contact moisture.
One thing to know from the start: Bradford Remodeling Co Houston is an independent contractor. We install Tamko fence systems and source compatible components, but we’re not a Tamko company and don’t speak for them. We speak for the work we do and the written price we hand you before anything gets torn out.
Which Tamko Models This Applies To
Tamko’s fence line breaks into two broad camps: vinyl privacy/ranch rail systems and composite deck-and-rail crossover products. The vinyl side includes their EverGrain and engineered rail profiles, which run in standard 6-foot panels with routed post channels, while the composite rail lines tie into Tamko’s deck boards for a matched look. The compatibility gotcha: a Tamko fence panel from one product generation often won’t seat cleanly into a post sleeve from another. The tongue profile and rail depth differ by 1/8 inch on some lines, which is enough to make a panel rock or bind.
Before you order anything, read the post cap. Tamko stamps the mold number on the underside of most vinyl caps, which tells us exactly which series you have. If the caps are gone, measure the wall thickness of the post sleeve in millimeters. The thinner 0.065-inch-wall sleeves are older builder-grade product; the newer residential lines run thicker. For OEM versus aftermarket: Tamko’s OEM panels carry the manufacturer warranty, but the lead time on special-order vinyl can stretch. A quality aftermarket panel matched to the same profile and wall spec installs the same, but the warranty is ours, not Tamko’s. We’ll price both ways and let you decide.
Styles & brands we work with
Signs Your Tamko Fence Installation Is Failing
- Post lean after heavy rain. Saturated clay soil in Houston loses holding strength, and a post set at only 18 inches deep will start drifting. We dig to 30 inches minimum for any replacement post in this market.
- Bottom rail sag between posts. Vinyl expands and contracts more than people expect, and if the original installer didn’t leave clearance at the post channel, the rail can buckle or crack at the corner blocks.
- Panels rattling in the wind. This usually means the internal rail clips or stiffeners were never installed, or the original crew used the wrong clip for the rail profile. A panel that moves in a Gulf Coast gust is a panel that eventually tears.
- Chalky, fading surface on the sun side. UV and heat take a toll faster in Houston than in most markets. Some Tamko vinyl products carry a fade warranty, but the real fix is matching the existing faded color line, not slapping a bright-white replacement panel into an aged run.
- Gate binding or dragging. Gates fail first on almost every fence. The hinge screws strip the post, the post flexes under the gate weight, and the latch misses. It’s a structural post problem, not just a hinge adjustment.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
The installed range for Tamko fence work in Houston: a typical 150-linear-foot full replacement runs $5,500 to $7,500 on level ground with one gate and standard post spacing. A smaller repair, like replacing a failed post and re-hanging two panels, falls in the $450 to $950 range. A full perimeter on a half-acre lot with multiple gates and old concrete to break out can push to $9,000 or more.
What drives the number: linear footage, gate count, soil conditions at the post line, whether we’re hauling off old fence, and whether the existing line is square or wanders. We write the scope and the price before work starts. No number moves at the door. Every Tamko fence job we complete carries our 365-Day Done Right Promise: if the work fails inside a year, we return and correct it at no charge.
DIY or Call Us?
You can safely check a few things yourself: walk the line and mark every leaning post, look for cracked caps, and photograph any panel that’s pulling loose. What you shouldn’t do is dig out a failed post and try to re-set it in Houston clay. The real problems hide below ground: undersized footings, post holes that filled with water and rotted the insert, or the entire post shifted because it was never concreted square. Vinyl fence posts under tension can also flex when you pull rails, and a cracked post can shatter at the cut line if it’s been sitting stressed all summer. We replace posts with a reinforced steel insert where the gate hangs, and the panel re-seating gets done with the correct clips, not whatever is left in the bucket.
If you’ve got a section that’s failed or a whole run that’s tired, call us at (940) 289-7658. We’ll send Curtis and a uniformed technician to measure, match the Tamko profile, and hand you a written scope and price before anything gets pulled.
FAQs
In Houston, a properly installed Tamko vinyl fence on 30-inch post footings typically lasts 20 to 25 years, though the sun-facing side will show visible fade within 8 to 10 years. Poorly installed posts at 18 inches, which are common on builder-grade jobs, can start leaning within 3 to 5 years. Call (940) 289-7658 and we’ll tell you whether your posts are set deep enough to be worth saving.
Yes, we can replace individual posts, rails, and panels, and we regularly match older Tamko profiles for spot repairs. The trick is matching the fade on the existing run, which is why we inspect the fence in daylight before pricing the repair. Call (940) 289-7658 for a written repair estimate.
A standard single-gate 150-foot installation gets set in two to three working days in Houston, assuming we’re not fighting old concrete or saturated ground from a recent storm. Larger runs with multiple gates or rotten post removal can run four to five. We’ll give you the day count in writing with your estimate.
We keep common Tamko-style post sleeves, caps, rail clips, and gate hinge kits in stock for most Houston repair calls, and we can source matching panels for the major Tamko vinyl and composite line within a few business days. If we don’t have your exact profile on the truck, we’ll photograph it, confirm the mold number, and give you an exact availability date before we schedule anything.
We also stock and install parts for KraftMaid, Cambria, and Silestone on the remodel side, so when the fence is sorted, we can talk about the rest of the house.
If your Tamko fence is failing or you’re ready to put in a new run, call Bradford Remodeling Co Houston at (940) 289-7658. We’ll walk the line with you, match the product, and hand you a written price. No pressure. No surprises. Just a fence that stands straight through the next Houston storm, backed by a one-year written guarantee.
Written by Curtis Lane, Owner, Bradford Remodeling Co Houston at Bradford Remodeling Co Houston, serving Houston and nearby areas.
