Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
CWS Fence Installation: The Houston Owner’s Guide
CWS fence installation in Houston typically runs $3,500 to $9,000 installed, depending on linear footage, gate count, and whether we’re pulling old posts or setting new ones in fresh concrete. We keep CWS-compatible post hardware, rails, pickets, and gate hinges on the truck for most common configurations, and a live person answers at (940) 289-7658 when you call. Most Houston owners discover the problem the hard way: a post leans after a heavy rain, a gate drags across the driveway, or pickets start popping loose after three or four summers of heat and humidity.
We’re an independent Houston contractor, not a CWS dealer or affiliate. What that means for you: we match the part to your existing CWS fence, quote a written price before we touch anything, and stand behind the install for a full year under our 365-Day Done Right Promise.
Key Takeaways
- CWS fence installation in Houston runs $3,500 – $9,000 installed, written quote before work starts
- We match current CWS profiles or source dimension-identical aftermarket equivalents
- Houston clay soil and humidity are the two biggest killers of fence posts and hardware
- Every install carries the 365-Day Done Right Promise: if it fails inside a year, we come back and fix it at no charge
Which CWS Models This Applies To
CWS fence products have shifted over the years, and the biggest compatibility gotcha we see in Houston is profile mismatch. Older CWS privacy fences used a 6-foot picket with a specific routed edge; some newer lines switched to a slightly thinner picket profile with a different tongue-and-groove angle. If you mix them on the same run, the seams open up within a season. We measure the existing picket thickness, the rail channel width, and the post gauge before we order anything, so we’re matching dimensions, not guessing from a photo.
Most CWS fence parts we install fall into three buckets: post-and-rail hardware (brackets, caps, post sleeves), gate componentry (hinges, latch posts, drop rods, wheel assemblies), and picket/rail replacement. For the post hardware, we prefer OEM CWS brackets when they’re still available because the screw hole spacing matches the existing posts. When OEM is discontinued, we use a dimension-identical aftermarket bracket and shim to spec. The reality in Houston is that aftermarket hardware often outlasts the original, especially in gate hinges, because the powder coat is heavier. We explain the choice in the written quote, not after the fact.
Bradford Remodeling Co Houston also stocks parts for KraftMaid, Cambria, and Silestone products, so if you have interior work on the same property, one call covers it.
Styles & brands we work with
Signs Your CWS Fence Installation Is Failing
- Posts leaning or twisting at the base. Houston’s gumbo clay expands and contracts with every rain-dry cycle, and a post set in a shallow footing will walk out of plumb within two or three years. The fix is pulling the post, re-setting it in a deeper concrete footing with gravel drainage, and re-hanging the rails.
- Gate dragging or sagging on the latch side. This is almost always a hinge failure or a post that’s lost its grip, not a gate that suddenly gained weight. The CWS gate hinge bolts we see fail first are the top hinges, which carry the most load when the gate swings.
- Pickets popping loose or cupping. Houston humidity will cup a thin picket in a single summer. Once a picket cups, it pulls the fasteners and opens gaps. Replacing individual pickets is cheap; leaving it lets water into the rails and speeds up rot.
- Rust bleed from hardware. In Houston’s humidity, uncoated or thin-coat brackets start rusting within two seasons. The rust is cosmetic at first, but it eventually eats the screw heads and the bracket body, and the rail loses its connection to the post.
- Rails bowing or pulling from brackets. Wind load during Houston storms will flex a rail repeatedly. If the bracket screws are undersized or the bracket is the wrong profile for the rail channel, the rail walks out of the bracket and the section starts flapping.
Replacement Cost & What’s Included
CWS fence installation in Houston runs $3,500 to $9,000 for a typical residential job. The range depends on three things: linear footage (most suburban lots run 150 to 300 feet), how many gates and corners are involved, and whether we’re reusing the existing posts or setting new ones. Post replacement adds the most cost because each post hole in Houston clay takes time to dig, gravel, set, and cure properly.
Every quote includes parts, labor, concrete for post footings, hardware match to your CWS profile, and haul-away of the old material. The price we write is the price you pay at the end. No change orders, no “we found an issue so it’s more now.” That’s the Garrison Standard, and Curtis Lane enforces it on every job. The finished work carries the 365-Day Done Right Promise: if a post shifts, a gate sags, or a rail pulls loose inside the warranty year, we come back and correct it at no charge.
Call (940) 289-7658 for a free estimate. Straight scope, straight number, that’s the whole conversation.
DIY or Call Us?
You can safely inspect your CWS fence without picking up a tool. Look for leaning posts, check gate hinge bolts with a wrench, and run your hand along the rails where they meet the brackets. If a bracket is loose, tighten the bolts and see if that solves it. That’s a five-minute check and it costs you nothing.
Where DIY goes wrong in Houston is post removal and re-setting. A post set in this clay will fight you coming out, and if you set the new one in the same old hole without gravel and proper depth, it’ll lean again within a season. Gate work has its own risk: a CWS gate with a wheel assembly is heavy, and if the post is compromised, the whole gate can drop while you’re working on it. If the post is moving or the gate is sagging, call (940) 289-7658 and let us put a crew on it. The estimate is free, and the written price means you decide with a number in front of you, not after we start.
See the difference
Before
After
Before
After
Before
AfterHow much does CWS fence installation cost in Houston?
CWS fence installation in Houston typically costs $3,500 to $9,000 installed, with most mid-size residential jobs landing between $4,500 and $6,500. The exact number depends on footage, gate count, and whether posts need re-setting. Call (940) 289-7658 for a written quote, no obligation.
Can you repair my existing CWS fence instead of replacing it?
Yes, and in many cases a repair makes sense if the posts are sound and only pickets, hardware, or a gate are failing. We’ll tell you straight if a repair buys you five more years or if you’re throwing money at a fence that needs full replacement. Either way, the quote is written before any work starts.
How long does a CWS fence installation take?
Most CWS fence installations in Houston take two to four working days from the first post hole to final cleanup, depending on footage and gate complexity. Post-setting in Houston clay needs time to cure before we hang rails, so we sequence the work to keep the fence plumb, not fast.
Do you stock CWS fence parts on the truck?
We stock the most common CWS-compatible brackets, hinges, post caps, and gate hardware on our trucks, and we source dimension-matched pickets and rails from local Houston suppliers within a day or two. For discontinued CWS profiles, we either match from remaining stock or mill the profile to spec. Call (940) 289-7658 and we’ll tell you what we can match before you spend anything.
Written by Curtis Lane, Owner, Bradford Remodeling Co Houston at Bradford Remodeling Co Houston, serving Houston and nearby areas.
