Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
ES Windows Fence Installation: The Houston Owner’s Guide
If you have an ES Windows fence section that’s failing, we stock compatible replacement parts and install them for a typical Houston price of $3,500 to $9,000, depending on the footage, post condition, and whether we’re repairing a run or replacing the whole fence line. Most owners discover the problem the same way: a gate that drags, a post that leans after a rain, or a panel that’s started to separate where the fence meets the house. ES Windows products are built to a specific tolerance, and when a fence installation fails, it’s usually the mounting hardware or the post footing, not the window product itself.
Bradford Remodeling Co Houston installs and services ES Windows fence systems across Houston, including Montrose, the Heights, Bellaire, Katy, Sugar Land, and Pearland. We’re an independent contractor, not affiliated with ES Windows, which means we tell you straight what’s worth fixing and what’s worth replacing. Curtis Lane has been running crews in the Houston market for over a decade, and he’s read enough scopes of work to know a failing fence installation when he sees one: the post base is the first thing to tell you the truth.
Which ES Windows Models This Applies To
ES Windows fence systems break into a few compatibility tiers, and the wrong part on the wrong series is a call-back waiting to happen. The fence installation components we handle cover the full ES Windows line: the ES Series, the Premium Series, and the Architectural Series. Each uses a different post profile and a different mounting channel. The ES Series runs a 2-inch square post with a face-mounted channel. The Premium Series uses a 2.5-inch post with a recessed track. The Architectural Series posts are 3-inch and heavier, built for taller fence runs where Houston wind load becomes a real factor. If you’re not sure which series you have, check the inside face of the post cap. ES Windows stamps the series code there, and it’s the fastest way to confirm what you’re working with before anyone cuts a single piece.
The OEM-versus-aftermarket decision on ES Windows parts is simpler than most brands make it. OEM post caps and mounting channels are worth paying for, because the stop-and-track tolerances on ES Windows fence lines are tight enough that a generic aftermarket cap will leave a visible gap and eventually let water sit in the post. Aftermarket post sleeves and decorative inserts are fine if they’re aluminum with a powder coat rated for coastal humidity. Houston’s heat and rain cycle is brutal on cheap powder coat; it blisters and the aluminum underneath pits. We stock OEM ES Windows post caps, mounting channels, and gate hardware on the truck. For post sleeves and inserts, we carry a documented aftermarket line from a mill that runs their coating to the same spec ES Windows requires on their Architectural Series.
We also stock compatible parts for KraftMaid, Cambria, and Silestone products, so if your fence line ties into a hardscape or an exterior kitchen, we’re not running back to a supply house mid-job.
Styles & brands we work with
Signs Your ES Windows Fence Installation Is Failing
- The gate drags or won’t latch. This is almost always a post that’s moved out of plumb, not a hinge problem. Houston clay soil expands in the spring and shrinks in August, and if the post footing wasn’t set below the shrink-swell line, the post shifts and the gate follows it.
- The post leans away from the house. Wind load on a solid ES Windows panel is real, especially on corner posts with no adjacent section bracing them. A post that’s leaning at the top but firm at the base means the footing is undersized for the panel it’s holding.
- Panels are separating at the seams. The channel between two fence panels opens when the mounting track has corroded or the set screws backed out. If left alone, water gets into the channel, sits there, and ruins the next section down the line.
- Water pools at the fence line after rain. A proper ES Windows fence installation grades water away from the post line. If you’re seeing standing water, the posts are sitting in a seasonal pond, and the aluminium is being asked to do something it was never spec’d for.
- Visible corrosion at post bases or mounting points. Houston humidity plus trapped moisture equals white powder and pitting on aluminum. It starts at the base, works up the post, and it doesn’t stop on its own. Once it’s visible on the outside, the inside of the post has been wet for a while.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full ES Windows fence installation in Houston runs $3,500 to $9,000, and the spread is driven by footage, post condition, and whether we’re pulling out old concrete footings or setting new ones. A short fence run of 40 to 50 linear feet with good posts and clean removal sits at the lower end. A full perimeter fence of 150 to 200 linear feet with failed posts, root intrusion, or a tie-in to an existing hardscape lands at the top of the range. We write the price down before work starts, every time. No numbers that move at the door, no change orders you didn’t ask for.
- Fence panel removal and disposal: $400 – $900 depending on footage and access.
- Post replacement (each): $180 – $400 including concrete footing and set.
- Mounting channel replacement (per 8-ft section): $60 – $140.
- Full ES Windows fence installation (40 – 200 linear ft): $3,500 – $9,000 installed.
Every ES Windows fence installation we complete is covered by the 365-Day Done Right Promise. If the work fails within one year, Bradford Remodeling Co Houston returns and corrects it at no charge. That’s the Garrison Standard, and we put it in writing on the estimate, not in a handshake.
DIY or Call Us?
What you can safely check on your own: post caps for cracks, panels for separation at the channel, and gate hinges for looseness. If you find loose set screws and you have the right hex key, snug them up. If the post itself is moving, stop there. Pulling a set ES Windows post and replacing it means getting the old footing out, matching the new concrete to the existing grade, and re-setting the post so the panel line runs true. It’s not high-tension work like a garage spring, but it’s easy to get wrong in a way that shows up later. A post that’s out of plumb by half an inch at the top becomes a full gate-slam problem in six months.
The other honest problem with DIY on ES Windows fence installations is the mounting channel. If it’s corroded, you’ll snap a screw head taking it off, and then you’re drilling out stainless steel in the August heat. That’s a miserable afternoon, and it’s exactly the kind of job we can knock out in a few hours with the right bits on the truck. Call (940) 289-7658 and we’ll give you a written price before any work starts.
FAQs
With proper footings and aluminum spec’d for humidity, an ES Windows fence installation lasts 20 to 25 years in Houston before the posts or mounting channels need major attention. If the footings were short or the coating was cheap aftermarket, you’ll see trouble in year 5 to 8. We check the post base first on every estimate; it tells us the remaining life of the whole fence line. Call (940) 289-7658 for a written price on your fence run.
Yes, when the posts are solid and the problem is isolated to mounting channels, post caps, or gate hardware, a repair makes sense and runs a few hundred dollars. When multiple posts have moved or the panels are corroding at the seams, you’re better off replacing the run at $3,500 to $9,000 than patching it every two years. We’ll tell you which one you have, with the price in writing either way.
Most residential fence installations we do take 2 to 4 working days from removal to final walk-through. Post footings need a day to set before we hang panels, and we don’t rush concrete cure in Houston heat; it weakens the set. You’ll have a written scope and a signed guarantee in your hand before we leave the site.
Yes. We keep OEM ES Windows post caps, mounting channels, and gate hardware on the truck, plus a documented aftermarket line of post sleeves and inserts spec’d for Houston humidity. If you need a specific Architectural Series part, we source it same week and the price is on your written estimate before we start. Call (940) 289-7658 and we’ll confirm it’s on the truck today.
Written by Curtis Lane, Owner, Bradford Remodeling Co Houston at Bradford Remodeling Co Houston, serving Houston and nearby areas.
