Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Jerith Driveway & Pavers: The Houston Owner’s Guide
We stock and install Jerith-compatible driveway gates, gate operators, and paver base components across Houston, with most parts matched and priced the same day you call. Installed driveway and paver work typically runs $7,000 to $18,000 depending on square footage, paver grade, and what’s underneath. The symptom picture is usually one of three things: a gate that won’t hold alignment, a sagging section of pavers where the base has washed out, or a bottom hinge plate that has pulled loose from its post.
Most Houston owners discover the failure after a heavy rain. The clay soil in this part of Texas expands and contracts more than most paver bases can take, and a Jerith gate that worked fine in October can bind by March. Bradford Remodeling Co Houston is an independent service provider, not affiliated with Jerith. We work on their products because we see a lot of them in this market, and because the parts are straightforward once you know what to look for.
Key takeaways:
- Jerith gate and paver parts are matched by post size, hinge offset, and latch throw, not just “Jerith” on the box.
- Installed driveway work in Houston runs $7,000 – $18,000. Sealing alone is $250 – $700.
- We give a written price before any work starts. No numbers move at the door.
- Every job carries the 365-Day Done Right Promise: if it fails within a year, we come back and correct it at no charge.
Which Jerith Models This Applies To
Jerith manufactures residential aluminum and steel driveway gates under several series lines: the Estate, Regal, and Sentry series are the ones we see most often in Houston, along with a smaller number of the newer Craftsman line. The part compatibility question is not just the series. It is the post size, the hinge style, and the latch mechanism. A Regal single-swing gate on a 4-inch square post takes a different hinge plate than the same gate on a 5-inch round post.
Here is the compatibility gotcha most homeowners miss: Jerith hinge plates are drilled for specific bolt patterns. If your post was installed by a different contractor, or if the gate was ever re-hung, the existing holes may not line up with a fresh Jerith plate. We see this constantly on homes in Katy and Sugar Land where the original installer used a generic hinge. The fix is either re-drilling with a plate that covers the old pattern, or stepping up to an aftermarket heavy-duty hinge with an adjustable offset. As a rule, OEM Jerith parts are worth the extra money on gate operators and latch assemblies, where the tolerances matter. Aftermarket equivalents are fine for hinge plates and post caps, where the spec is just gauge and hole pattern.
If you can, check the sticker on the gate frame near the bottom rail. Jerith stamps the series and a date code there on most gates made after 2010. If the sticker is gone, measure the post and photograph the hinge while the gate is open. That gets us to the right part on the first trip.
Styles & brands we work with
Signs Your Jerith Driveway & Pavers Is Failing
- The gate drags on the driveway surface. This usually means the bottom hinge has worn or the post has shifted. In Houston’s clay soil, posts move more than people think. A gate that drags today will bind completely within a few months.
- The gate won’t stay latched in the wind. The latch throw has worn down, or the striker plate has drifted. Houston gets enough gusty storm fronts that a marginal latch will fail at the worst possible time.
- Pavers are sinking near the gate posts. This is a base failure. Water has gotten under the pavers and washed the fines out. The pavers are fine; what is underneath them is gone.
- The operator makes a grinding noise or hesitates. The gear train in Jerith operators is sealed, but the arm and bracket are not. Houston humidity corrodes the pivot points, and the motor works harder until it quits.
- You see hairline cracks running through multiple pavers. This is a subgrade problem, not a paver problem. The base was compacted poorly or the soil beneath it has shifted. Replacing individual pavers will not fix it.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
In Houston, Jerith driveway gate and paver work falls into these ranges:
- Gate hinge or latch replacement: $150 – $450 installed, depending on whether we are swapping like-for-like or re-drilling for a heavier plate.
- Gate operator replacement: $800 – $2,200 installed, depending on swing vs. slide and the arm configuration.
- Paver driveway installation: $7,000 – $18,000 for a full driveway, base included.
- Paver driveway repair (sectional): $800 – $3,500, depending on how much base has to come out and whether we are re-using the existing pavers.
- Driveway sealing: $250 – $700, including cleaning and joint sand.
The range is driven by three things: how much base work the soil requires, the paver grade, and access. A driveway in Meyerland with a long narrow side entrance costs more in labor than a wide-open drive in Cypress. Our price is written before we start, and it covers the parts, the labor, the base work, and cleanup. The Garrison Standard means the number we hand you is the number you pay. If the work fails within a year, the 365-Day Done Right Promise brings us back to correct it at no charge.
DIY or Call Us?
There are things an owner can safely check. You can inspect the hinge bolts for looseness. You can look at whether pavers have dropped more than a quarter inch from the surrounding grade. You can test the latch by closing the gate and trying to jostle it open. That information helps us quote accurately over the phone.
What you should not do is attempt to lift a sagging gate and re-hang it yourself. A double-swing Jerith gate can weigh over 200 pounds per leaf, and when the hinge gives way, the gate drops fast. We have seen fingers and wrists broken by gate work in Houston. Gate operators also carry electrical load, and the arm is under tension even when the power is off. This is not a place to learn as you go. Call us at (940) 289-7658 and we will get a tech out to look at it.
FAQs
A Jerith aluminum gate in Houston typically lasts 12 to 20 years before the hinges, latch, or operator need real attention. Steel gates tend to run 10 to 15 years, and the failure point is almost always corrosion at the weld joints from humidity and rain exposure. Pavers, by contrast, can last 25 years or more if the base was built right, but the base itself may need work every 7 to 10 years in Houston’s expansive clay. Call (940) 289-7658 and we will tell you what you are actually looking at before you spend a dollar.
Yes, in most cases. Hinges, latches, operators, and post anchors are all replaceable parts, and we repair more Jerith gates than we replace. The times replacement makes more sense are when the gate frame itself is corroded through, or when the post has shifted far enough that re-hanging becomes a structural problem rather than a hardware problem. We will show you the condition in writing before we recommend anything. Estimates are free at (940) 289-7658.
Most gate part replacements are finished in one visit, typically 2 to 4 hours, and that includes testing the swing and the latch under load. A sectional paver repair usually takes one to two days because the base has to be excavated, re-compacted, and the pavers re-set and sanded. A full paver driveway runs 3 to 7 days depending on square footage. We will give you a written schedule with the written price. Call (940) 289-7658 to get yours.
We keep common Jerith hinge plates, latch assemblies, and operator arms on the truck, along with base materials and the paver brands we install most in Houston, including Belgard and Unilock. If your part is series-specific and we do not have it on hand, we order it directly and schedule the install as soon as it lands, usually within 5 to 7 business days. Straight scope, straight number, that is the whole conversation. Call (940) 289-7658 and we will confirm what we have before you schedule.
Written by Curtis Lane, Owner, Bradford Remodeling Co Houston at Bradford Remodeling Co Houston, serving Houston and nearby areas.
