Free written scope consultation - allowances, timeline, and change-order rules on paper before a single trade is scheduled
Barrette Kitchen Remodeling: The Houston Owner’s Guide
If you have a Barrette kitchen and a part has failed, here’s the straight answer: a full Barrette kitchen remodel in Houston runs $14,000 to $45,000, but if you’re only replacing a failed component like a cabinet door, drawer glide, or counter section, most of our Barrette-specific fixes land between $400 and $2,500 installed. We stock Barrette-compatible hardware on our trucks and can usually match your existing finish and spec within one visit. Most Houston homeowners discover the failure the hard way: a drawer that suddenly sticks, a hinge that sags by a quarter inch, or a counter seam that opens up after a humid August.
Bradford Remodeling Co Houston is an independent service provider. We are not affiliated with Barrette, but we work on their products every week and know where the weak points are.
Key Takeaways:
- Barrette kitchen remodel in Houston: $14,000 – $45,000 installed for a full project.
- Individual part replacements: $400 – $2,500 depending on part and labor.
- We match existing Barrette finishes, hinge patterns, and drawer glide specs.
- Every installed part carries our 365-Day Done Right Promise in writing.
- Call (940) 289-7658 for a written quote before any work starts.
Which Barrette Models This Applies To
Barrette kitchen cabinetry comes in a few distinct product lines, and the hardware is not always interchangeable across them. If you have a Barrette frameless cabinet, the hinges are typically 35mm cup, full-overlay, and the door gap should be 3mm. If you have their face-frame line, you’re looking at 1/2-inch overlay hinges with a completely different mounting plate. Mixing those up is the number one compatibility mistake we see in Houston homes, especially in older neighborhoods like Sharpstown and Braeswood where remodels have changed hands a few times.
Match the part before you buy. Look for a manufacturer label inside the cabinet door or on the drawer box side. If the label is gone, measure the hinge cup diameter (35mm is standard for Barrette), the overlay (how far the door covers the face frame), and the drawer glide length. Our crews carry a documented Barrette hardware reference sheet so we can identify what you have on the first trip. For OEM versus aftermarket: Barrette’s OEM hardware is fine, but we regularly install Blum or Salice equivalents that last longer in Houston’s humidity at a lower price than OEM. We will tell you when aftermarket makes sense and when it does not.
Styles & brands we work with
Signs Your Barrette Kitchen Remodeling Is Failing
- Drawer glides that grind or catch. Barrette’s older side-mount glides lose their ball bearings after years of Houston humidity and heavy use. The drawer still opens, but it fights you, and eventually the glide pulls out of the cabinet side.
- Hinges that sag or doors that won’t close flush. When the hinge arm bends or the cup loosens, the door drops. You’ll see a wider gap at the top than the bottom. This is almost always a hinge replacement, not a door replacement.
- Counter seams that open or lift. Barrette counters with laminate or solid-surface tops can separate at seams when the substrate swells. Houston’s humidity is brutal on particleboard substrates. Once the seam opens, water gets in and the problem accelerates.
- Soft-close mechanisms that slam. The little dampener inside the hinge or glide fails first. The cabinet still functions, but the slam tells you the dampener is dead. We replace just the dampener when the hinge body is still good.
- Corner cabinet hardware (lazy Susan or blind corner pull-out) that binds. Barrette’s corner units use a specific pivot geometry. When the bearing wears, the shelf catches on the frame. Forcing it bends the pivot rod, and then the whole unit needs replacing.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
A full Barrette kitchen remodel in Houston runs $14,000 to $45,000, and that spread is driven by cabinet count, counter surface, and how much structural work the existing layout requires. For individual part failures, our installed pricing looks like this:
| Part or Scope | Houston Installed Price |
|---|---|
| Hinge replacement (per door) | $40 – $90 |
| Drawer glide replacement (per drawer) | $60 – $140 |
| Soft-close dampener replacement | $25 – $60 |
| Counter seam repair | $300 – $1,200 |
| Cabinet door replacement | $150 – $400 per door |
| Full Barrette kitchen remodel | $14,000 – $45,000 |
Every line item is written down before we start. Parts, labor, and the warranty term are all in the written quote. The 365-Day Done Right Promise covers the installed part and the labor for a full year. If it fails inside that window, we return and correct it at no charge. That is the Garrison Standard, and it applies to every Barrette part we install.
DIY or Call Us?
Some things are safe to check yourself. You can tighten a hinge plate with a #2 Phillips, and you can clean a drawer glide with a dry rag and a silicone spray. One caution on silicone: do not spray it near a gas cooktop with a live flame. Turn the gas off first, or use a dry lubricant. Those are low-risk fixes that can buy you a few more months.
But if a hinge is bent, a glide has lost bearings, or a counter seam has opened, call us. The risk with DIY is that you install the wrong spec part, drill into a cabinet frame, and now the fix costs more than the original problem. Barrette face-frame and frameless cabinets look similar at a glance, and we have pulled out plenty of wrong-size hinges that homeowners installed the week before. You do not have to guess. Call (940) 289-7658 and get a written quote for the specific part and labor. Curtin Lane or one of our techs will walk you through what we found and what it costs.
FAQs
Expect 15 to 20 years from Barrette cabinet hardware in a Houston kitchen, but in high-humidity homes without good ventilation, hinges and glides can start failing in as little as 8 to 10 years. The dampeners go first.
We can repair a hinge if only the mounting plate is loose. If the hinge arm is bent or the dampener is shot, replacement is the honest fix. We price the part and labor separately on every written quote.
Most hinge and glide replacements take 20 to 40 minutes per door or drawer. A counter seam repair takes 2 to 4 hours including cure time. The quote we hand you has the labor window in writing.
We keep common Barrette-compatible hinges, glides, dampeners, and mounting plates on our trucks. We stock parts for KraftMaid, Cambria, and Silestone as well. If we need a specific Barrette OEM part, we order it and schedule the repair as soon as it arrives. Call (940) 289-7658 for availability and a written quote.
Written by Curtis Lane, Owner, Bradford Remodeling Co Houston at Bradford Remodeling Co Houston, serving Houston and nearby areas.
